fuse3d · SLS · Fuse 1+ 30W · material datasheet
PA12 (Nylon 12 Powder)
Our base SLS powder for rigid parts and production series.
MATERIALSSLS · Fuse 1+ 30WNylon 12 Powder
PA12
Our base SLS powder for rigid parts and production series.
PA12 for housings, fixtures and production series. Specimen data show a higher tensile modulus than PA11, but lower notched impact strength and elongation at break. We prepare a reviewed quotation for international orders.
Manufacturer datasheet (PDF)Powder handling and quotation
- refresh rate
- 30%
- The share of fresh powder added to each build. It determines the variable material cost more directly than the listed price of a powder bag.
- build chamber atmosphere
- Air
- Where the manufacturer permits printing a nitrogen-grade powder in air, we use a higher refresh rate and include it in the quotation.
- individual quotation
- reviewed quote
- A technologist will confirm the price, powder availability and lead time after reviewing the model and quantity.
When to use this material and when to avoid it
＋ Choose it when
- Tensile modulus of 1,850 MPa (ASTM D638 Type 1), useful when selecting a material for rigid parts.
- Housings, fixtures and mounting surfaces; we select fits for the geometry and working conditions.
- Small mass changes in 24-hour tests with selected oils and solvents; the results and media are listed below.
- Powder surrounds the part during printing, so the part needs no supports.
− Avoid it when
- Notched Izod impact strength of 32 J/m (ASTM D256-10), lower than PA11 specimen results. For impact exposure, we also assess the part design, temperature and loads.
- Elongation at break 11% in X/Y and only 6% in Z axis, so a flexible latch must be consciously oriented.
- HDT of 87 °C at 1.8 MPa (ASTM D648) is a specimen test result. Part service temperature is assessed with exposure time, load and mounting.
- Water absorption of 0.66% (ASTM D570) describes a specimen, not part dimensional change. Fits require assessment of the geometry and measurement conditions.
Keep this datasheet for your records: the print version contains the material values and test standards without navigation or calls to action.
Mechanical properties
Values with test standards
Formlabs Nylon 12 Powder TDS (2201730)
Scroll the table sideways to see the remaining columns.
| Property | Value | Test standard |
|---|---|---|
| Tensile Strength | 50 MPa | ASTM D638 Type 1 |
| Modulus of Elasticity in Tension | 1 850 MPa | ASTM D638 Type 1 |
| Elongation at Break | 11% · 6%X/Y · Z | ASTM D638 Type 1 |
| Flexural Strength | 66 MPa | ASTM D790-15 |
| Flexural modulus | 1 600 MPa | ASTM D790-15 |
| Izod impact strength, notched | 32 J/m | ASTM D256-10 |
X/Y is the powder spreading plane, Z is the build direction. The difference between axes is not a measurement error but a process characteristic. How we choose build orientation.
Thermal and physical properties
Temperature and moisture
Scroll the table sideways to see the remaining columns.
| Property | Value | Test standard |
|---|---|---|
| HDT at 1.8 MPa | 87 °C | ASTM D648 |
| HDT at 0.45 MPa | 171 °C | ASTM D648 |
| Vicat softening temperature | 175 °C | ASTM D1525 |
| Water absorption (part) | 0.66% | ASTM D570 |
| Flammability at 3.00 mm | HB | UL 94 |
| Specimen biocompatibility per manufacturer tests | non-cytotoxic, non-irritating, non-sensitizing | ISO 10993-1:2018 |
HDT is the temperature at which a test specimen reaches a specified deflection, not a part's allowable continuous service temperature. 0.45 MPa and 1.8 MPa are two test stresses; the lower value does not mean no load. For material selection, tell us the temperature, exposure time, load and mounting method.
PA12 and PA11: samples conditioned for 7 days at 50% relative humidity and 23 °C, per manufacturer datasheets. The TPU 90A datasheet does not state the same conditioning protocol. Results depend on geometry, orientation, temperature and humidity; they describe test specimens, not guaranteed part properties.
Chemical resistance
Mass change after 24 h
1 cm³ cube
Scroll the table sideways to see the remaining columns.
| Medium | Mass change after 24 h | Assessment |
|---|---|---|
| Water | 0.1% | test result |
| 3.5% NaCl brine | 0.2% | test result |
| Acetone | 0.1% | test result |
| Isopropanol | 0.2% | test result |
| Xylene | 0.1% | test result |
| Isooctane (TDS: gasoline) | <0.1% | test result |
| Hydraulic oil | 0.6% | test result |
| Heavy mineral oil | 0.7% | test result |
| Skydrol 5 | 0.6% | test result |
| Hydrogen Peroxide 3% | 0.2% | test result |
| Concentrated Hydrochloric Acid | 0.8% | test result |
The immersion test ran for 24 h on a 1 cm³ cube. Mass change may indicate absorption or degradation, but does not determine part service life. A low value does not confirm suitability for continuous contact. Tell us the medium, concentration, temperature and contact duration for an application review.
Compare another powder
Sources: Formlabs Nylon 12 Powder TDS (2201730). The manufacturer PDF is linked below. We do not accept medical devices or safety-critical parts. Specimen biocompatibility data describes the material in manufacturer tests, not the compliance of a finished product.
Manufacturer datasheet (PDF)Quote a model in PA12
Send the model, quantity and destination country. We confirm material suitability, international pricing and delivery terms individually.
Quote a model in PA12 I don't have a modelQuick contact
Need help choosing a material?
Leave your phone number or email. Tell us where the part will work and what loads it needs to withstand.
Loading the form details. Please wait a moment.